30.5×30.5mm Holybro KAKUTE F4 V2.4 Tekko32 F4 Metal 4in1 65A ESC Stack F4 MPU6000 OSD Flight Controller 5V 9V BEC Support Analog Digital HD Atlatl HV V2 0.5-800mW VTX for RC Drone FPV Racing yuup.co.za

Kakute F4 v2.4 Flight Controller

( Manual)

MCU: STM32F405
IMU: MPU6000
Barometer: BMP280
OSD: AT7456E
5x UARTs (1,3,4,4,6,7)
128 Mbit Dataflash chip
Battery input voltage: 2S-8S
BEC 9V/3A – Optimized for DJI O3 Air unit
BEC 5V/2A
7x PWM Outputs (6 Motor Output, 1 LED)
Supports serial receivers (SBUS, iBus, Spektrum, TBS CRSF, ESLR).
Mounting – 30 x 30mm, Φ4mm hole with M3 Grommets
Dimension – 37x37mm
Weight – 7g
JST-SH1.0_8pin port (For 4in1 ESCs)
JST-SH1.0_6pin port (For DJI/Caddx HD System and other VTX) 

Tekko32 F4 Metal 4in1 65A ESC

( Pin Cable)

Continuous Current: 65A x4
Burst Current: 75A x4
Supports 4-6S battery
Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.
ESC telemetry Supported
Onboard analog current sensor
No output BEC
BLHeli_32 firmware
1000uf 35v capacitor included (highly recommended for 6s setup)
Amperage meter scale ratio: 180 
Dimensions: 43 x 44mm / Weight: 15.8g
Mounting holes: M4 30.5×30.5mm (M3 grommets included)

Features:

New & faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)
PWM Frequency: 16k to 96k
Metal-cased MOSFET for excellent heat dissipation
Massive on-board capacitance for noise filtering at 2068uf
3 oz copper PCB design to allow bigger current and better heat dissipation
Separate drive & control circuit, 

this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.

With VTX Version

( Manual)

Model: Atlatl HV V2 VTX

Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
Audio: 6.5 MHz Mono
Protocol?smart audio2.0
Antenna Connector: MMCX
Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts
Dimensions: 35x25x7mm (Includes USB height)
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 9.3g

( VTX Table Link )

1x KAKUTE F4 V2.4 FC

1x Tekko32 F4 Metal 4in1 65A ESC
1x Electrolytic capacito: 1000uF 35v 
1x  8pin to 8pin 1mm pitch 65mm cable
1x  8pin to 8pin 1mm pitch 25mm cable
1x  JST SH 6pin to JST GHR 8pin 80mm &150mm cable (for DJI/Caddx HD System)
1x  JST SH 6pin 100mm cable(for Caddx HD Systems)

1x KAKUTE F4 V2.4 FC

1x Tekko32 F4 Metal 4in1 65A ESC

1x Atlatl HV V2 VTX

1x Electrolytic capacito: 1000uF 35v 
1x 8pin to 8pin 1mm pitch 65mm cable
1x 8pin to 8pin 1mm pitch 25mm cable
1x JST SH 6pin to JST GHR 8pin 80mm &150mm cable (for DJI/Caddx HD System)
1x JST SH 6pin 100mm cable(for Caddx HD Systems)
1x 80mm SMA–MMCX Cable
1x JST GHR 4pin 150mm cable